Tasks

Tasks

List of Tasks. You have to respond to all of these in your blog.

Please number your tasks in your blog so they can be found easily.

1. Start your blog.

2. Edit the permissions in your blog so that just prjbrook@gmail.com is invited to see it.

3. Make sure you can access the Arduino environment. Find the Blink program in the examples and paste into your blog. Test that it compiles in the Arduino IDE but you don't have to send it to your Arduino yet.

4. What is the name of the Atmel microprocessor in your Arduino board? Insert the link to the large pdf from Atmel associated with this chip. Insert an image of the first page of this pdf. Finally insert a picture of the pin-out of this chip.

5. Find the forum associated with main Arduino site. Take a screen shot of something in the forum that interests you with a comment on what appeals to you.

6. Find a picture of your Arduino  publish it in your blog and label the main parts. You may need a special graphics program to do this. Add another interesting Arduino variation. You can see some on this page.

7. Put the url for your blog into the wiki in Moodle. Add some other contact details. If you wish your cell phone number to remain private that's OK too.

8. Check out the following sites. Insert a screen shot and a URL link into your blog. Small images or large ones are both OK .
The Arduino environment version 1.5 or (stop press) 1.6.
The Processing environment.
The Fritzing files.
Link to Blogger.
GNU gcc
Moodle
AVR Studio download. Latest version.
PDF of ATMega 328
PDF of specs of USB-to_serial chip. The one used in the Duemilanove.
Good pic of our arduino clone
The MindKits site.
One cool video on Youtube.
One other interesting internet resources. eg "Make" site or electonics sites.
The Nice Gear store in Timaru that sells good Arduinos.

9. Find 4 more Arduino LED related videos in Youtube, BlipTV etc. Put a link and a two-sentence review about each one in your blog. Be prepared to talk about one or more of them to the class.

10. Establish a sketchpad folder in the D Drive or in a USB pen or somewhere you can get to.

All programs from now on need their source code to be entered into your blog with comments. Make sure you comment the the top of your blog posting with the number of the task and enter too the task number as a //coment in your code.

11. Copy the famous Blink program to your blog and make sure you can run it on you Arduino.

12. Create a variation in timing and put your new program into your blog. Indicate with a comment what your change was.

13. Write a program that will have the LED mostly off. That is it only blips on once a second if you look closely.

14. Same as 13 but this time have your LED mostly on.

15. Repeat 14 with an external LED on a breadboard.

16. Copy the two LED program into your blog and run it.

17. Insert a variation so that the LEDs blink together.

18. Write a program so that one LED is blinking fast while the other blinks slowly.

18.1 View the little video on resistors at this site . Attach a colour code table to your blog and take a photo of three of your resistors in your kit with their resistances shown in text labels near each resistor.

18.2 (Look at analog pins.) Pin A0 will read any voltage value between 0 and 5 volts. Set up your Arduino board so that its circuit looks like the Fritzing diagram on this site. Run the program and make a change with a comment in your blog.

(Now looking at serial monitor.)

19. Copy the ASCII printing program from http://arduino.cc/en/Tutorial/ASCIITableand run it. A good background site is the lady ada serial tutorial.

20. Find 5 RS232 devices you can use with an Arduino. Put the names and the functions in a list. Show a picture of a pin out where one of the devices is connected to an Arduino.

21.  Find 5 I2C devices you can use with an Arduino. Put the names and the functions in a list. Show a picture of a pin out where one of the devices is connected to an Arduino.